| MANUAL CONTROL FADER |
 |
CPA-T-9100 Series |
| Conductive plastic resistor element used (Low slide noise). Best touch. Horizontal style control-bar design (Protection against dust). Durable system which adopted the shaft of the high quality. All models include a touch sense track. |
| Last update: 2023.12.19. | [Electrical-spec] | [Mechanical-spec] | [Note] | [Dimensions] | [Model-number] | EU-RoHS |
| Information |
| Due to a delay in parts
procurement, the color of the main body (label side) has been changed to
gray. This will not affect the use of the product. If you cannot change the color, please contact our sales department. |
| Electrical specifications (initial value) |
CPA-T-9100 Series | ||
| Products | CPA-T-910*-B* | CPA-T-910*-A* | CPA-T-910*-AP* |
| Number of circuits Type of output laws |
1 Law1: Linear taper |
2 Law1: Linear taper Law2: Audio taper |
2 Law1: Linear taper Law2: AP taper |
| Circuit method (Output law1) | Potentiometer circuit | ||
| Circuit method (Output law2) | - | Ladder circuit |
|
| Total resistance (1-C), (1-3) | 10kohm, 5kohm | ||
| Total resistance tolerance | ±20% | ||
| Absolute linearity (Linear taper) | ±5% (The travel is divided into 10 sections and 11 positions are measured.) | ||
| Residual voltage (1-2), (2-3) (Linear taper) |
10mV or less |
||
| Residual resistance (1-2), (2-3) (Linear taper) |
30ohm or less (Reference values) |
||
| Touch sense track contact resistance |
20ohm or less (Between terminal 4 and Control-bar.) |
||
| Attenuation accuracy [Load: high] |
- | 0 - 20dB: ±1.0dB (10dB: ±0.5dB) - 40dB: ±2.0dB (Audio taper, AP taper) |
|
| Insertion loss | - | 0.5dB or less (Audio taper, AP taper) | |
| Cut off [15kHz] | - | 100dB Min. (Audio taper, AP taper) | |
| Voltage proof | 1 Min. at AC500V | ||
| Insulation resistance | 50Mohm or more at DC500V | ||
| Max rating | 0.2W (Linear taper), 0.1W (Other taper) | ||
| Maximum input voltage | DC30V or less | ||
| Rated Resistive Load - Switch | AC125V 3A, DC30V 2A (OMRON D2F-F) | ||
| Sliding noise level | 47mV or less (by JIS C 6443) | ||
| Sliding life | 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV) | ||
| Mechanical specifications (initial value) |
CPA-T-9100 Series |
| Travel (Stroke) length | 100mm ±0.5mm |
| Operating force | 0.03 to 0.2N |
| Strength Nut-Attached | 100Ncm |
| Attached parts | M3 screw (Length: Panel thickness + 3mm) |
| Stopper strength | 40N |
| Push-pull strength | 40N |
| Alignment to the center | ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface) |
| General specifications | CPA-T-9100 Series |
| Temperature range | -10 to +50 degrees C (Operating), -15 to +60 degrees C (Storage) |
| Relative humidity | 80%RH (No condensation) |
| Note |
| * Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual
soldering only) * Please take care during soldering that the smoke from the solder does not flow inside a fader. * If the flux sticks to a resistor board, it may cause a trouble with the fader. |
| * Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly. |
| * It is highly recommended that the fault tolerant system is to be set up in the big situation like the live broadcast. |
| * Operating force is lighter than other CPA-9000 series. * This product is designed on the assumption of the horizontal use. * The enough operational testing is highly recommended for the slant or the vertical use to prevent the unexpected operation. |
| *The terminal arrangement and numbering is the same as the MF-9000 series of motor faders, unlike the CPA-9000 series of manual faders. |
| * Replacing it from other brands tests it enough, and please consider. |
* Caution in Ladder circuit(Audio and AP taper) use. Important points in using audio curve and log curve of TKD faders >>  |
| * Color may vary slightly due to body material. * Due to the way the body is processed, there may be some rubbing on the folded parts. |
| * A simple resistor maintenance procedure is presented. Please try
it when you need it. However, we do not guarantee the product after this work. * Please provide your own equipment. >> 1st step
, 2nd step
, 3rd step
|
| Dimensions - CPA-T-910*-** | ||||||||||||||||
 |
||||||||||||||||
|
| Dimensions - Panel cut out |
 |
| Dimensions - Terminations |
 |
| Model number | ||||||||||||
|
| *1 | Product number | CPA-T-910 : CPA-T-9100 Series |
| *2 |
Control-bar length: Length (Bracket height) |
1 : 9mm (5mm) 2 : 11mm (7mm) |
| *3 |
Precision Snap Action Switch |
Blank : Without W : With |
| *4 |
Output law |
B : Linear taper + Touch sense track A : Linear taper + Audio taper + Touch sense track AP : Linear taper + AP taper + Touch sense track |
| *4 |
Total resistance |
10K : 10kohm 5K : 5kohm |
| Products No. ( X: Standard model) |
Travel | Output law1 |
Output law2 |
Resistance law1 |
Resistance law2 |
Touch sense track |
Snap action switch |
Mounting Screws |
Control-bar length (Bracket height) |
|
| CPA-T-9101-B10K | X | 100mm | Linear | - | 10kohm | - | With | Without | M3 | 9mm (5mm) |
| CPA-T-9101-B5K | 100mm | Linear | - | 5kohm | - | With | Without | M3 | 9mm (5mm) | |
| CPA-T-9101-A10K | 100mm | Linear | Audio | 10kohm | 10kohm | With | Without | M3 | 9mm (5mm) | |
| CPA-T-9101-A5K | 100mm | Linear | Audio | 5kohm | 5kohm | With | Without | M3 | 9mm (5mm) | |
| CPA-T-9101-AP10K | 100mm | Linear | AP | 10kohm | 10kohm | With | Without | M3 | 9mm (5mm) | |
| CPA-T-9101-AP5K | 100mm | Linear | AP | 5kohm | 5kohm | With | Without | M3 | 9mm (5mm) | |
| CPA-T-9101-B10K | X | 100mm | Linear | - | 10kohm | - | With | With | M3 | 9mm (5mm) |
| CPA-T-9101-B5K | 100mm | Linear | - | 5kohm | - | With | With | M3 | 9mm (5mm) | |
| CPA-T-9101-A10K | 100mm | Linear | Audio | 10kohm | 10kohm | With | With | M3 | 9mm (5mm) | |
| CPA-T-9101-A5K | 100mm | Linear | Audio | 5kohm | 5kohm | With | With | M3 | 9mm (5mm) | |
| CPA-T-9101-AP10K | 100mm | Linear | AP | 10kohm | 10kohm | With | With | M3 | 9mm (5mm) | |
| CPA-T-9101-AP5K | 100mm | Linear | AP | 5kohm | 5kohm | With | With | M3 | 9mm (5mm) | |
| CPA-T-9102-B10K | X | 100mm | Linear | - | 10kohm | - | With | Without | M3 | 11mm (7mm) |
| CPA-T-9102-B5K | 100mm | Linear | - | 5kohm | - | With | Without | M3 | 11mm (7mm) | |
| CPA-T-9102-A10K | 100mm | Linear | Audio | 10kohm | 10kohm | With | Without | M3 | 11mm (7mm) | |
| CPA-T-9102-A5K | 100mm | Linear | Audio | 5kohm | 5kohm | With | Without | M3 | 11mm (7mm) | |
| CPA-T-9102-AP10K | 100mm | Linear | AP | 10kohm | 10kohm | With | Without | M3 | 11mm (7mm) | |
| CPA-T-9102-AP5K | 100mm | Linear | AP | 5kohm | 5kohm | With | Without | M3 | 11mm (7mm) | |
| CPA-T-9102-B10K | X | 100mm | Linear | - | 10kohm | - | With | With | M3 | 11mm (7mm) |
| CPA-T-9102-B5K | 100mm | Linear | - | 5kohm | - | With | With | M3 | 11mm (7mm) | |
| CPA-T-9102-A10K | 100mm | Linear | Audio | 10kohm | 10kohm | With | With | M3 | 11mm (7mm) | |
| CPA-T-9102-A5K | 100mm | Linear | Audio | 5kohm | 5kohm | With | With | M3 | 11mm (7mm) | |
| CPA-T-9102-AP10K | 100mm | Linear | AP | 10kohm | 10kohm | With | With | M3 | 11mm (7mm) | |
| CPA-T-9102-AP5K | 100mm | Linear | AP | 5kohm | 5kohm | With | With | M3 | 11mm (7mm) | |
| Update list | |
| 2023.12.19. | Addition of maximum input voltage specification. Change in maximum ratings. |
| 2023.08.24. | Add maintenance information. |
| 2023.08.04. | Added note on body material. |
| 2023.07.20. | Slight correction of specification notations. Specification 4-40UNC screw deleted. |
| 2023.03.29. | Additional 3D data (step format). |
| 2022.11.01. | First edition |