English   Japanese   
TOP         PRODUCTS         TECHNOLOGY         DISTRIBUTORS         PRODUCT STATUS
     MANUAL CONTROL FADER

CPA-9100 Series
Conductive plastic resistor element used (Low slide noise).
Best touch.
Horizontal style control-bar design (Protection against dust).
Durable system which adopted the shaft of the high quality.
3 types of output linear-laws.
Last update: 2025.07.31. [Specifications] [Note] [Dimensions] [Model-number] [Update list] EU-RoHS


Information
The cover and frame material will be changed from Electrolytic zinc-coated steel sheets to SPCC with cation electrodeposition coating.
(Sequentially carried out from april 21st, 2025.)

Change the material of the resistive element. (Sequentially carried out from may 21st, 2025.)


Electrical specifications
(initial value)		 CPA-9100 Series
Products CPA-910*-B* 2CPA-910*-B* CPA-910*-LB* 2CPA-910*-LB*
Number of circuits
Type of output laws		 1
Linear taper		 2
Linear taper x2		 1
Long linear taper		 2
Long linear taper x2
Circuit method Potentiometer circuit
Total resistance (1-C) 10kohm,   5kohm
Total resistance tolerance ±20%
Absolute linearity
 ±5% (The travel is divided into 10 sections and 11 positions are measured.)
Residual voltage (1-2), (2-3) 10mV or less -
Residual resistance (1-2), (2-3) 30ohm or less (Reference values) 200ohm or less (Reference values)
Voltage proof 1 Min. at AC500V
Insulation resistance 50Mohm or more at DC500V
Max rating 0.2W
Maximum input voltage DC30V or less
Rated Resistive Load - Switch AC125V 3A, DC30V 2A (OMRON D2F-F)
Sliding noise level 47mV or less (by JIS C 6443)
Sliding life 100,000 Cycles Min. (18cycles/min, Sliding noise level: Less than 100mV)

Mechanical specifications
(initial value)		 CPA-9100 Series
Travel (Stroke) length 100mm ±0.5mm
Operating force
 		 0.1 to 0.25N (Standard)
0.2 to 0.4N (High operating force / Center click)
Strength Nut-Attached 100Ncm
Attached parts M3 screw / 4-40UNC screw (Length: Panel thickness + 3mm)
Stopper strength 50N
Push-pull strength 40N
Alignment to the center ±0.5mm (State not to pressure control-bar, Measurement position: Mounting surface)

General specifications CPA-9100 Series
Temperature range -10 to +70 degrees C (Operating), -15 to +75 degrees C (Storage)
Relative humidity 90%RH (No condensation)


Please check before use.
* Solder heat resistance: 350deg C max, 5sec max, 2 times. (Manual soldering only)
* Please take care during soldering that the smoke from the solder does not flow inside a fader.
* If the flux sticks to a resistor board, it may cause a trouble with the fader.
* Move to one end in Control-bar on the occasion of knob wearing, and can break into it slowly.
* It is highly recommended that the fault tolerant system is to be set up in the big situation like the live broadcast.
* This product is designed on the assumption of the horizontal use.
* The enough operational testing is highly recommended for the slant or the vertical use to prevent the unexpected operation.
* Only high operating force type with CP-1 or CP2 is applicable for the vertical use.
* Replacing it from other brands tests it enough, and please consider.
* A simple resistor maintenance procedure is presented. Please try it when you need it.
  However, we do not guarantee the product after this work.
* Please provide your own equipment.

    >>  1st step ,  2nd step ,  3rd step
* Please do not strike the fader carriage hard against either end of the fader.


Outline
CPA-9101 CPA-9101W
2CPA-9101 2CPA-9101W
CPA-9102 CPA-9102W
2CPA-9102 2CPA-9102W

Panel cut out

Terminations


Model number
2 CPA-910 1 C W - C - UNC - B 10K
*1 *2 *3 *4 *5   *6   *7   *8 *9

*1
 		 Number of circuits
 		 Blank : Single circuit
2         : Two circuits
*2 Product number (Travel) CPA-910 : CPA-9100 Series 100mm
*3
 		 Control-bar length: Length (Bracket height)
 		 1 : 9mm (5mm)
2 : 11mm (7mm)
*4
 		 Operating force

 Blank : Standard
C        : High operating force
*5
 		 Precision Snap Action Switch
(Center click is not selectable.)		 Blank : Without
W        : With
*6
 		 Click option
 		 Blank : Without
C        : Center click (Linear taper only)
*7
 		 Mounting threads
 		 Blank : M3
UNC   : 4-40UNC
*8
 		 Output law
 		 B   : Linear taper
LB : Long linear taper
*9
 		 Total resistance
 		 10K : 10kohm
5K   : 5kohm


    Model Number Search 

  • CPA-9101-B10K      *
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9101-B5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9102-B10K      *
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9102-B5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9101C-B10K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9101C-B5K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9102C-B10K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9102C-B5K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9101W-B10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9101W-B5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9102W-B10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9102W-B5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9101CW-B10K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9101CW-B5K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9102CW-B10K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • CPA-9102CW-B5K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • CPA-9101-C-B10K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • CPA-9101-C-B5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • CPA-9102-C-B10K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • CPA-9102-C-B5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • CPA-9101W-C-B10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • CPA-9101W-C-B5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • CPA-9102W-C-B10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • CPA-9102W-C-B5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9101-B10K      *
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9101-B5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9102-B10K      *
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9102-B5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9101C-B10K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9101C-B5K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9102C-B10K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9102C-B5K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9101W-B10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9101W-B5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9102W-B10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9102W-B5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9101CW-B10K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9101CW-B5K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9102CW-B10K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9102CW-B5K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9101-C-B10K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9101-C-B5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9102-C-B10K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9102-C-B5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9101W-C-B10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9101W-C-B5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • 2CPA-9102W-C-B10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, M3)
  • 2CPA-9102W-C-B5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, M3)
  • CPA-9101-UNC-B10K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9101-UNC-B5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9102-UNC-B10K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9102-UNC-B5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9101C-UNC-B10K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9101C-UNC-B5K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9102C-UNC-B10K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9102C-UNC-B5K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9101W-UNC-B10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9101W-UNC-B5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9102W-UNC-B10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9102W-UNC-B5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9101CW-UNC-B10K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9101CW-UNC-B5K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9102CW-UNC-B10K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • CPA-9102CW-UNC-B5K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • CPA-9101-C-UNC-B10K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • CPA-9101-C-UNC-B5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • CPA-9102-C-UNC-B10K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • CPA-9102-C-UNC-B5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • CPA-9101W-C-UNC-B10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • CPA-9101W-C-UNC-B5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • CPA-9102W-C-UNC-B10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • CPA-9102W-C-UNC-B5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101-UNC-B10K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101-UNC-B5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102-UNC-B10K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102-UNC-B5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101C-UNC-B10K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101C-UNC-B5K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102C-UNC-B10K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102C-UNC-B5K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101W-UNC-B10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101W-UNC-B5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102W-UNC-B10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102W-UNC-B5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101CW-UNC-B10K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101CW-UNC-B5K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102CW-UNC-B10K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102CW-UNC-B5K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101-C-UNC-B10K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101-C-UNC-B5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102-C-UNC-B10K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102-C-UNC-B5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101W-C-UNC-B10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101W-C-UNC-B5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102W-C-UNC-B10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102W-C-UNC-B5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Linear taper, Resistance 5kohm, UNC)
  • CPA-9101-LB10K      *
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9101-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9102-LB10K      *
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9102-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9101C-LB10K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9101C-LB5K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9102C-LB10K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9102C-LB5K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9101W-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9101W-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9102W-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9102W-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9101CW-LB10K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9101CW-LB5K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9102CW-LB10K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • CPA-9102CW-LB5K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • CPA-9101-C-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • CPA-9101-C-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • CPA-9102-C-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • CPA-9102-C-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • CPA-9101W-C-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • CPA-9101W-C-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • CPA-9102W-C-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • CPA-9102W-C-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9101-LB10K      *
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9101-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9102-LB10K      *
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9102-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9101C-LB10K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9101C-LB5K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9102C-LB10K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9102C-LB5K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9101W-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9101W-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9102W-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9102W-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9101CW-LB10K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9101CW-LB5K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9102CW-LB10K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9102CW-LB5K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9101-C-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9101-C-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9102-C-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9102-C-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9101W-C-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9101W-C-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • 2CPA-9102W-C-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, M3)
  • 2CPA-9102W-C-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, M3)
  • CPA-9101-UNC-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9101-UNC-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9102-UNC-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9102-UNC-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9101C-UNC-LB10K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9101C-UNC-LB5K
    (Single circuit, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9102C-UNC-LB10K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9102C-UNC-LB5K
    (Single circuit, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9101W-UNC-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9101W-UNC-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9102W-UNC-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9102W-UNC-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9101CW-UNC-LB10K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9101CW-UNC-LB5K
    (Single circuit, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9102CW-UNC-LB10K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9102CW-UNC-LB5K
    (Single circuit, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9101-C-UNC-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9101-C-UNC-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9102-C-UNC-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9102-C-UNC-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9101W-C-UNC-LB10K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9101W-C-UNC-LB5K
    (Single circuit, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • CPA-9102W-C-UNC-LB10K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • CPA-9102W-C-UNC-LB5K
    (Single circuit, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101-UNC-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101-UNC-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102-UNC-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102-UNC-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101C-UNC-LB10K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101C-UNC-LB5K
    (Two circuits, 9mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102C-UNC-LB10K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102C-UNC-LB5K
    (Two circuits, 11mm control-bar, High operating force, Without snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101W-UNC-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101W-UNC-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102W-UNC-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102W-UNC-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101CW-UNC-LB10K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101CW-UNC-LB5K
    (Two circuits, 9mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102CW-UNC-LB10K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102CW-UNC-LB5K
    (Two circuits, 11mm control-bar, High operating force, With snap action switch, Without click option, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101-C-UNC-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101-C-UNC-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102-C-UNC-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102-C-UNC-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, Without snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9101W-C-UNC-LB10K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9101W-C-UNC-LB5K
    (Two circuits, 9mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  • 2CPA-9102W-C-UNC-LB10K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 10kohm, UNC)
  • 2CPA-9102W-C-UNC-LB5K
    (Two circuits, 11mm control-bar, Standard operating force, With snap action switch, Center click, Long linear taper, Resistance 5kohm, UNC)
  (* is the standard model)
   After selecting each specification, the model number for ordering appears at the top.
   (If blank, there is no target model.)

   Number of circuits : Single circuit Two circuits
   Control-bar length : 9mm 11mm
   Operating force type : Standard High
   Option snap action switch : Without With
   Center click option : Without Center click
   Mounting threads : M3 4-40UNC
   Output law : Linear taper Long linear taper
   Total resistance value : 10kohm 5kohm
    When reloading the browser, please press Reset once.




Update list
   
2025.07.31. Separate datasheets for Audio and AP specifications.     Addition of long linear taper specification.
2025.05.08. Deletion of note on body material and Extra high operating force version.
2025.04.11. Change in cover and frame materials.     Change the material of the resistive element.
2025.01.22. Added operational notes.
2024.03.13. Add Extra high operating force version.     Introduction of model number search.
2023.12.19. Addition of maximum input voltage specification.     Change in maximum ratings.
2023.08.24. Add maintenance information.
2023.08.04. Added note on body material.
2023.07.20. Slight correction of specification notations.
2023.03.29. Additional 3D data (step format).
2022.11.01. First edition